Silicone Leveling Agent
|
Product number |
material composition |
Exterior |
Content |
Features |
Scope of application |
Recommended dosage |
|
SD-6333 |
Polyether modified polydimethylsiloxane |
light yellow liquid |
100% |
It can drastically reduce the surface tension of the coating system, especially improve the wettability of the substrate, prevent shrinkage, and at the same time, improve the surface smoothness and gloss.
|
For solvent-free, solvent-borne and waterborne coating systems and printing inks |
0.05-0.3 % Additive dosage (as supplied) Based on the total formulation, up to 1 % can be added for aqueous and UV systems.
|
|
SD-6334 |
Polyether modified siloxane copolymer |
Transparent to slightly yellow liquid, no obvious odor |
100% |
It can improve fluidity, transparency in varnishes, improve slipperiness, anti-shrinkage effect, anti-blocking/peeling effect, etc. It has good recoatability and minimal influence on interlayer adhesion. |
It can be used universally in water-based, radiation-cured and solvent-borne coating formulations, while providing high performance, high compatibility (extremely low probability of haze). |
General dosage: 0.03%-0.2%, 0.5%-1% in UV system |
Wetting agent
|
product name |
Features |
Viscosity (25℃, mPa.S) |
Scope of application |
Recommended dosage |
|
SD-6270 |
High performance, excellent anti-crater effect, good recoatability and additional flow promotion.
|
30±10 |
For water-based formulations, also suitable for radiation-cured formulations |
General dosage: 0.1%-1%
|
|
SD-6271 |
This additive does not provide foam stabilization, nor does it increase surface slip and does not impair recoatability.
|
20±10 |
Silicone Surfactants for Aqueous Systems |
General dosage: 0.1%-1%
|
|
SD-6272 |
Silicone surfactant with strong reduction of surface tension and significantly improved substrate wetting. Does not increase surface slip.
|
120±50 |
For waterborne coatings, printing inks and overcoats |
General dosage: 0.05-0.5%
|
|
SD-6273 |
It can wet the substrate, prevent shrinkage crater, and promote flow and defoaming properties. |
450±100 |
Water-based formulation for wood coatings, industrial coatings, printing inks and varnishes.
|
General dosage: 0.1%-1%
|
Defoamer
|
product name |
Features |
Viscosity (25℃, mPa.S) |
Scope of application |
Recommended dosage |
|
SD-6270 |
High performance, excellent anti-crater effect, good recoatability and additional flow promotion.
|
30±10 |
For water-based formulations, also suitable for radiation-cured formulations |
General dosage: 0.1%-1%
|
|
SD-6271 |
This additive does not provide foam stabilization, nor does it increase surface slip and does not impair recoatability.
|
20±10 |
Silicone Surfactants for Aqueous Systems |
General dosage: 0.1%-1%
|
|
SD-6272 |
Silicone surfactant with strong reduction of surface tension and significantly improved substrate wetting. Does not increase surface slip.
|
120±50 |
For waterborne coatings, printing inks and overcoats |
General dosage: 0.05-0.5%
|
|
SD-6273 |
It can wet the substrate, prevent shrinkage crater, and promote flow and defoaming properties. |
450±100 |
Water-based formulation for wood coatings, industrial coatings, printing inks and varnishes.
|
General dosage: 0.1%-1%
|
Pesticide Synergist
|
product name |
Viscosity (25℃, mPa.S) |
Surface Tension |
Features |
wettability |
permeability |
|
SD-5408 |
20-50 |
≤20.5 mN/m |
It has super spreading, permeability, efficient internal absorption, conductivity, and resistance to rain erosion |
★★★★★ |
★★★★★ |
